SINGLE PHASE M AND THREE-PHASE T / Y
|POWER RANGE||From 5 to 4000 kVA, in single-phase and three-phase version.|
|ACCURACY||±1% RMS also in presence of high harmonic distortions.|
|OVERLOAD CAPACITY||10 times the rated power for 10 ms, 5 times for 6 s, 2 times for one minute|
|POWER FACTOR AND LOAD VARIATION INSENSITIVITY||The accuracy and the regulation speed remain unaltered under any load condition (full load or no load, with inductive or capacitive loads).|
|FREQUENCY VARIATION INSENSITIVITY|
|HARMONIC DISTORTIONS||The harmonic distortion is always maintained within 0.2% in any operating condition|
|IMPEDANCE||The installation of an Ecostab voltage optimiser in a preexisting plant does not require a new calculation of the protections because the internal impedance of the optimiser does not significantly affect the line impedance.|
|OPERATING TEMPERATURE||Ecostab voltage optimisers are designed for operation at a maximum ambient temperature of 40°C in the most demanding conditions: continuous duty, full load and minimum input voltage. Models suitable for higher temperatures are manufactured on request.|
|DEGREE OF PROTECTION||IP00, IP21, IP54 INDOOR and IP54 OUTDOOR|
|COOLING SYSTEM||All IP21 models are designed for natural air convection – FAN-FREE. IP54 models are cooled by fans or by air conditioning depending on the ambient conditions.|
|RELIABILITY||Ecostab voltage optimisers use the same technology and the same components as Ministab and Sterostab voltage stabilisers, that IREM has been manufacturing for over 60 years. The MTBF exceeding 500,000 hours is the result of IREM continuous improvement in technical aspects and production process.|
|INSTALLATION||The voltage optimiser is installed after the energy counter and before the electric users.|
|STANDARD FITTINGS||Digital network analyser / energy meter, pilot lamps, potentiometer, alarm indication and dry contacts for connection to an external device for protection against: overload, over/under voltage|
|SPECIAL VERSIONS||Ecostab voltage optimisers can be equipped on demand with special fittings in separate cabinet, like e.g.: maintenance bypass, thermal magnetic circuit breakers, surge/lightning arresters, harmonic filters.|
|REMOTE CONTROL||Ecostab voltage optimisers can be equipped with an optional monitoring system permitting the remote control via ETHERNET, INTERNET, GSM/GPRS.|
|COMPLIANCE WITH STANDARDS||
Ecostab voltage optimisers comply with the following Directives:
The Ecobuck supplies the load with a stable voltage having a lower value or at the limit equal to the nominal mains voltage.
The voltage with which the load is powered can be set through a potentiometer between the nominal value and -8%.
The behavior of the Ecobuck differs from that of the Ecostab only when the mains voltage is less than the desired voltage.
In conditions of voltage lower than the desired value, the Ecobuck does not worsen the supply conditions, simply the load is powered at the voltage it would be powered on if there was no Ecobuck.
If the mains voltage drops to 375V, for example, the Ecobuck would deliver 375V to the load. As soon as the mains voltage returns to a value higher than the set value (for example 382V), the Ecobuck returns to operate by adjusting the voltage on the load.
SINGLE-PHASE 230V 50/60HZ VOLTAGE OPTIMISERS – IP21 INDOOR MODELS
THREE-PHASE 400V 50/60HZ VOLTAGE OPTIMISERS – IP21 INDOOR MODELS
THREE-PHASE + N 400V 50/60HZ VOLTAGE OPTIMISERS – IP21 INDOOR MODELS
Standard fittings: Potentiometer to adjust the stabilised output voltage; Digital network analyser and energy meter; Display and storage of saving data in absolute value and %; Communication port: ETHERNET, USB; Alarm indication and dry contacts for connection to an external device for protection against: overload, over/under voltage; Pilot lamps.
Optional fittings: Polycarbonate screen for IP2x protection at open doors (for “AJB” models in cabinet); Class II or Class I+II surge arresters; Connection to the iremON remote service.
IREM voltage optimisers are designed to deliver the declared power permanently (24/7) under the worst operating conditions, i.e. at full load, at minimum ECOSTAB S SINGLE PHASE M AND THREE-PHASE T / Y input voltage and max input current and at the declared ambient temperature
An electronic control circuit detects the voltage delivered by the voltage optimiser and compares it to a reference voltage. If the difference between the output voltage and the reference voltage exceeds the preset tolerance limits, an error signal is generated; this signal may be either negative or positive according to whether the output voltage is lower or higher than the preset value. This signal activates the servomotor which moves the mobile contacts (electrographite rollers / brushes) of the variable autotransformer thus changing the transformation ratio in order to supply the additive or subtractive voltage needed to restore the value within the predetermined limits to the primary winding of the series transformer. The rootmean-square value (RMS) of the output voltage is stabilised and consequently not affected by possible harmonic distortions present in the input mains. This regulation system has the advantage of not having mobile contacts in series to the power supply line.